2002 - 2005 Jeep Liberty AC Compressor

New SD7H15 Air Conditioning A/C Compressor Complete With 6 Groove Clutch Assembly For Jeep Liberty V6 3.7.
$138.12
List Price: $414.35
You save $276.23
Part # 30697N
Available
Quantity:

New SD7H15 A/C Compressor fits the following vehicles:

  • Jeep Liberty (2004) - V6 3.7L GAS
  • Jeep Liberty Limited (2002 - 2005) - V6 3.7L GAS
  • Jeep Liberty Renegade (2003 - 2005) - V6 3.7L GAS
  • Jeep Liberty Rocky Mountain Edition (2005) - V6 3.7L GAS
  • Jeep Liberty Sport (2002 - 2005) - V6 3.7L GAS
Sanden SD7H15 Compressor With 6 Groove Clutch Assembly Measuring 5.23" Diameter, 2.1" (From Big Right Ear) Gauge Line
 
Labor time to remove and replace the A/C compressor is .7 hours, not including evacuate and recharge.
 
REMOVAL 
WARNING: Refer to the applicable warnings and cautions for this system before performing the following operation.  Failure to follow the warnings and cautions could result in possible personal injury or death.
 
NOTE: The A/C compressor may be removed and repositioned without disconnecting the refrigerant lines or discharging the refrigerant system. Discharging is not necessary if servicing the A/C clutch, clutch field coil or the engine.
 
1. Recover the refrigerant from the refrigerant system.
2. Disconnect and isolate the negative battery cable.
3. Remove the serpentine drive belt.
4. Disconnect the wire harness connector from the A/C clutch field coil.
5. Depending on the engine usage, remove the bolts or nuts that secure the suction and discharge lines to the A/C compressor and remove and discard the O-ring seals.
6. Install plugs in, or tape over all of the opened refrigerant line fittings and compressor ports.
7. Remove the bolts or nuts that secure the A/C compressor to the engine.
 
 
8. Remove the A/C compressor from the engine compartment.
 
INSTALLATION
NOTE: If a replacement A/C compressor is being installed, be certain to check the refrigerant oil level. See Refrigerant Oil Level in this group for the procedures. Use only refrigerant oil of the type recommended for the A/C compressor in the vehicle. (this new compressor comes with a full charge of oil)
 
1.  Position the A/C compressor into the engine compartment.
2.  On the 3.7L gasoline engine install all mounting bolts hand tight, then tighten the mounting bolts in the following sequence:
    The rear bolt to 55 N·m (41 ft. lbs.).
    The front inboard bolt to 40 N·m (30 ft. lbs.).
    The front outboard bolt to 55 N·m ( 41 ft. lbs.).
3.  Remove the tape or plugs from the opened refrigerant line fittings and compressor ports.
4.  Lubricate new rubber O-ring seals with clean refrigerant oil and install them on the discharge and suction line fittings. Use only the specified O-rings as they are made of a special material for the R-134a system. Use only refrigerant oil of the type recommended for the A/C compressor in the vehicle.
5.  Install the suction and discharge lines onto the A/C compressor.
6.  Install the bolts or nuts (depending on engine application) that secure the suction and discharge lines to the A/C compressor. Tighten the bolts or nuts to 28 N·m (20 ft. lbs.).
7.  Connect the wire harness connector to the compressor clutch field coil.
8.  Install the serpentine drive belt.
 
 
9.  Reconnect the negative battery cable.
10.  Evacuate the refrigerant system.
11.  Charge the refrigerant system.
 
The Accumulator or Filter Drier should always be replaced when the Air Conditioning System is opened.  (see why)  The Orifice Tube, if equipped, should always be replaced and the Expansion Valve, if equipped, should at least be inspected for proper operation if not replaced.  (see why)
Denso: 471-7026
Discount AC Parts: 60-01581RC, 60-01581NA, 60-01581NC
Frigette: 204-1578, 204-1579
Four Seasons: 67576, 68576
Jeep: 5503 7466AC, 5503 7466AE
Proliance: 1436N
Sanden: 4335, 4852